To simulate aircraft might suffer lightning or for the damage caused by the internal electronics, DO160section22 part gives the detailed test method, this system fully meet RTCA DO - 160 - g version of the standard, can be used to lightning transient induction test, airborne equipment can meet the test of airbus, Boeing and other airlines requirements, at the same time can meet the latest GJB 8848 lightning conduction coupled injection test. In addition, in order to save the test cost, developed a special can meet DO160 level 4 of the following tests (can meet more than 95% of the daily testing tasks) of equipment, at the same time compatible with the latest edition of the MIL - STD - 461 - g CS117 lightning military equipment cable transmission caused by sensitivity test, the device adopts the design of more integrated, only need a cabinet to complete a single response experiment and back many times, greatly saving the configuration time. This system can be widely used in the lightning indirect effect transient induction test of electronic systems of aerospace, aviation, vehicles, ships and various military equipment, and can also be used in other related research and experiments.
Damage effect on aircraft structures and other parts.Standard
SAE ARP5412 Aircraft Lightning Environment And Related Test WaveformsCharacteristic
FSG-160MS(W1、W4、W5)
FSG-160MB(W2、W3、W6)
Waveform selection module
FSG-160MS |
FSG-117MS |
|
The basic parameters |
||
DO160Test level |
Grade five(W1,W4,W5A,W5B) |
Grade four( W1,W4,W5A,W5B) |
CS117Test level |
Completely satisfied |
Completely satisfied |
Equipment appearance |
The two cabinets are connected in parallel |
A single cabinet |
The equipment size |
35UTwo cabinets |
35UOne cabinet |
W1Current waveform output capability (medium width pulse) |
||
Short circuit current waveform(μs) |
6.4/69 |
6.4/69 |
The source port outputs the current(A) |
Up to 3500A |
Up to 2000A |
Minimum interval time(s) |
20s to 999 |
10s to 999 |
Single return amplitude( V / A) |
Up to 3500A |
Up to 2000A |
Multiple return amplitude (first time/subsequent, A / A) |
Up to 2000A/1000A |
Up to 1000A/500A |
W4Waveform parameters (medium width pulse) |
||
Open circuit voltage waveform(μs) |
6.4/69 |
6.4/69 |
Short circuit current waveform(μs) |
6.4/69 |
6.4/69 |
Source port output voltage(V) |
Up to 2500V |
Up to 1500V |
Source port output voltage(A) |
Up to 500A |
Up to 300A |
Minimum interval time(s) |
20s to 999 |
10s to 999 |
Pin injection output amplitude(V / A) |
Up to 2500V/500A |
Up to 1500V/300A |
Single return amplitude( V / A) |
Up to 2500V |
Up to 1500V |
Multiple return amplitude (first time/subsequent, V / V) |
Up to 1600V/800V |
Up to 900V/450V |
W5AWaveform parameters (long pulse) |
||
Open voltage waveform(μs) |
40/120 |
40/120 |
Short circuit current(μs) |
40/120 |
40/120 |
Source port output current(A) |
Up to 5500A |
Up to 3000A |
Minimum interval time(s) |
30s to 999 |
20s to 999 |
Pin injection output amplitude ( V / A) |
Up to 3000V/3000A |
Up to 1800V/1800A |
Single return amplitude( V / A) |
Up to 10000A (2T:1T) |
Up to 5000A (2T:1T) |
Multiple return amplitude (first time/subsequent, A / A) |
Up to 4000A/2000A |
Up to 3000A/1500A |
W5BWaveform parameters(Long pulse,optional) |
||
Open voltage waveform(μs) |
50/500 |
50/500 |
s) |
50/500 |
50/500 |
Source port output current(A) |
Up to 3000A |
Up to 2000A |
Minimum interval time(s) |
50s to 999 |
30s to 999 |
Pin injection output amplitude( V / A) |
Up to 1900V/1900A |
Up to 1000V/1000A |
Single return amplitude( V / A) |
Up to 5000A (2T:1T) |
Up to 3000A (2T:1T) |
Multiple return amplitude (first time/subsequent, A / A) |
Up to 2000A/1000A |
Up to 1000A/500A |
Basic parameters |
|
DO160Test level |
Grade five |
CS117Test level |
Completely satisfied |
Device appearance |
A single cabinet |
The equipment size |
Two 5U cases can be installed in 35U cabinet |
W2Voltage waveform output capacity (short pulse) |
|
Open voltage waveform(μs) |
0.1/6.4 |
Source port output voltage(V) |
2000V |
Minimum interval time(s) |
10s to 999 |
Single return amplitude( V / A) |
Up to 2000V |
Multiple return amplitude (first time/subsequent, A / A) |
Up to 2000V/1000V |
W3-1MHz /10MHzOscillating waveform output capability |
|
Open voltage waveform(μs) |
1MHz、10MHz(Damped wave) |
Short circuit current waveform(μs) |
1MHz、10MHz(Damped wave) |
Source port output voltage(V) |
4000V |
Source port output current(A) |
128A |
Minimum interval time(s) |
10s to 999 |
Pin injection output amplitude( V / A) |
Up to 4000V/128A |
Single return amplitude( V / A) |
Up to 4000V |
Multiple return amplitude (first time/subsequent, A / A) |
Up to 4000V/2000V |
Pulse group amplitude( V / A) |
Up to 3000V |
W3-1MHz /10MHzOscillating waveform output capability |
|
Short circuit current waveform(μs) |
0.25/4 |
Source port output current(A) |
200A |
Minimum interval time(s) |
10s to 999 |
Pulse group amplitude( V / A) |
Up to 200A |
Waveform selection module |
|
Waveform selection module
|
Model:FSG-160-MOD-L1 Attenuation waveform amplitude for grade 1 and grade 2 testing, It is suitable for W4, W5A and W5B waveforms Mainly used for PIN injection test and cable bundle test Need to cooperate with fsg-160 or fsg-117 generator. |
|
FSG-160-MOD-JG35 Adopt 35U standard cabinet, consistent with FSG160 and other equipment appearance The fsb-160mb series waveform module can be conveniently stored neatly Built-in 2 4U host storage slots Built-in 4 standard module storage slots Slide guide for easy placement Solve the problem of disorderly storage of all waveform modules in laboratory. |
Test the module selection |
|
|
FSG-160-LCT-W15 Current coupled transformers For W1, W5A, W5B current waveform coupling Can meet the cable bundle W1, W5A, W5B waveform single return, multiple return grades 1-5 test Maximum coupling W1 waveform 4kA (1T: 1T) Maximum coupling W5A waveform 10kA (2T: 1T) Maximum coupling W5B waveform 5kA (2T:1T) |
|
FSG-160-LVT-W45 Voltage coupled transformers For W4, W5A, W5B voltage wave coupling Can meet the cable bundle W4, W5A voltage waveform single return, multiple return grade 1-5 test Maximum coupling W4 voltage waveform 1600V (5T: 5T) Maximum coupling W5A voltage waveform 1600V (7T: 7T) Maximum coupling W5B voltage waveform 300V (10T: 10T) |
|
FSG-160-LVT-W23 High frequency voltage coupling transformer Used for W2, W3 (1MHz, 10MHz) voltage waveform coupling Can meet the cable bundle W2, W3 voltage waveform single return, multiple return, and multiple pulse group level 1-5 test Maximum coupling W2 voltage waveform 2000V Maximum coupling W3 voltage waveform 4000V |
|
FSG-160-LVT-W6 High frequency current coupling transformer For W6 current waveform coupling Can meet the cable beam W6 current waveform of multiple pulse group level 1-5 test Maximum coupling W6 current waveform 160A |
|
FSG-160-CN-W45 Power coupling unit Used for coupling W4, W5A and W5B waveforms Maximum voltage of isolated ac/dc power supply is 400V Ac USES pressure-sensitive couplers, containing 130V, 250V and 420V3 grades The coupling below dc 200V is capacitively coupled, and the pressure-sensitive coupling can be used above 200V |
|
DN-416T-COM Power supply decoupling unit Used for decoupling and coupling of W4, W5A and W5B waveforms Maximum voltage of ac/dc power supply: 3-phase 400V 16A, 0-800hz (common mode) Single-phase filtering is realized by using common mode inductor and decoupling capacitance It can satisfy the power test with W4, W5A and W5B waveforms injected by pins |
Lisn-4580d line impedance stable network Used for cable bundle test to isolate radio interference and provide stable test impedance Inductance: 5 x H (to meet LISN requirements of DO160) The maximum voltage of ac/dc power supply is 450V 80A Three - phase power supply power supply needs to use 4 at the same time. CAP-33000 capacity For use with LISN in cable bundle test Maximum voltage of dc power supply: 400V The capacitance is 33000uF |
|
Measure and match accessories |
|
|
MDO3052 Tektronix series digital oscilloscope Frequency: 500Mhz; sampling rate: 1.25gs /s The storage depth is 10Mb and can be used to test multiple return strokes and pulse group waveforms |
|
P5664 Current sensor Pearson, caliper, peak current 200kA, 0.001V/A Maximum charge of 8As Test the current waveform of W1, W4, W5A, and W5B |
|
THDP0100 The differential probe American teck, 6kV differential mode, 100MHz frequency Can be used to measure voltage signal of all waveforms |
A100 voltage attenuator Damping ratio:100:1 The highest input 4000V Frequency 400MHz, used for measuring W3, W2 high-frequency voltage waveform |
|
CS10 coaxial current attenuator 0.1V/A,frequency400MHz Used to measure the current waveform of W3, W6. |
|
Cn-w3 high frequency capacitive coupler Pulse coupling for W2, W3, and W6 waveforms Meet the requirement of power supply for W2, W3, W6 pin injection test. |
|
|
HIP-W236 Handheld pins are injected into the probe For insertion of W2, W3, and W6 waveforms, The hand-held structure is designed to facilitate the surge injection of the pin of the product under test Maximum working voltage is 10kV. |
|
Mobile test vehicle With a weight of 500kg, it can be folded Hydraulic lift, with cardan wheel, up to 01M It can be used as a testing platform for heavy coupler and other desktop instruments such as LCT, LVT, etc |
D1548 test table Fully solid wooden table design Can choose 2mm aluminum or copper board desktop Can choose reference to receive floor With sizes of 0.8M*1.5M*0.8M, 1.2M*2.4M*0.8M, 1.5M*4.8M*0.8M, etc Other sizes can also be customized |